What are the tips for using geared motors
2020年12月12日1. After the geared motor has been running for 200 to 300 hours,the oil
should be changed for the first time, and the oil quality should be checked regularly in the future use. The oil mixed with impurities or deteriorated should be replaced in time. Under normal circumstances, for long-term continuous working geared motors, the new oil should be replaced after 5000 hours of operation or once a year. For geared motors that have been out of service for a long time, they should also be replaced with new oil before restarting. Mixed use, oils of the same grade but different viscosity are allowed to be mixed.
2. When changing the oil, wait for the geared motor to cool down and there is no danger of burning, but it should still be kept warm, because after complete cooling, the viscosity of the oil increases and it is difficult to drain the oil. Note: Cut off the power supply of the transmission device to prevent accidental power-on!
3. During work, when the oil temperature rises above 80°C or the oil pool temperature exceeds 100°C and abnormal noise is found, stop using it. Check the cause, remove the fault, and replace the lubricating oil before continuing to run.
4. The user should use and maintain the rules and regulations of the gear reduction motor reasonably, and carefully record the operation of the gear reduction motor and the problems found during the inspection. The above regulations should be strictly implemented.
Inspection and maintenance:
Gear motor transmission lubricant
Grease selection When selecting the grease according to the bearing load of the gear reduction motor, the grease with a small penetration degree should be selected for heavy loads. When working under high pressure, in addition to low penetration, it also has higher oil film strength and extreme pressure performance. When selecting grease based on environmental conditions, calcium-based grease is not easily soluble in water and is suitable for dry and low-water environments. When selecting grease according to working temperature, the main indicators should be dropping point, oxidation stability and low-temperature performance. The dropping point can generally be used to evaluate high-temperature performance. The actual working temperature of the bearing should be 10-20℃ lower than the dropping point. The use temperature of synthetic grease should be 20-30℃ lower than the dropping point.
should be changed for the first time, and the oil quality should be checked regularly in the future use. The oil mixed with impurities or deteriorated should be replaced in time. Under normal circumstances, for long-term continuous working geared motors, the new oil should be replaced after 5000 hours of operation or once a year. For geared motors that have been out of service for a long time, they should also be replaced with new oil before restarting. Mixed use, oils of the same grade but different viscosity are allowed to be mixed.
2. When changing the oil, wait for the geared motor to cool down and there is no danger of burning, but it should still be kept warm, because after complete cooling, the viscosity of the oil increases and it is difficult to drain the oil. Note: Cut off the power supply of the transmission device to prevent accidental power-on!
3. During work, when the oil temperature rises above 80°C or the oil pool temperature exceeds 100°C and abnormal noise is found, stop using it. Check the cause, remove the fault, and replace the lubricating oil before continuing to run.
4. The user should use and maintain the rules and regulations of the gear reduction motor reasonably, and carefully record the operation of the gear reduction motor and the problems found during the inspection. The above regulations should be strictly implemented.
Inspection and maintenance:
Gear motor transmission lubricant
Grease selection When selecting the grease according to the bearing load of the gear reduction motor, the grease with a small penetration degree should be selected for heavy loads. When working under high pressure, in addition to low penetration, it also has higher oil film strength and extreme pressure performance. When selecting grease based on environmental conditions, calcium-based grease is not easily soluble in water and is suitable for dry and low-water environments. When selecting grease according to working temperature, the main indicators should be dropping point, oxidation stability and low-temperature performance. The dropping point can generally be used to evaluate high-temperature performance. The actual working temperature of the bearing should be 10-20℃ lower than the dropping point. The use temperature of synthetic grease should be 20-30℃ lower than the dropping point.
コメント